Product Information
Features
・Master Section
Newly designed 4-band EQs for Treble, Hi-Mid, Low-Mid, and Bass, with a wide variable Freq knob for Hi-Mid and Low-Mid, allowing you to adjust the bandwidth and create a wide variety of sounds. The Hi-Mid and Low-Mid can be adjusted by the Freq knob, which has a wide variable range, and the Bright switch to emphasize the attack, and the Notch switch to cut the middle naturally, allowing you to pursue detailed sound creation.
・Drive Section
The new circuit design is based on the sound character of the Rhinotes, which was a big hit. With a wide range of gain and a 2-band EQ dedicated to distortion Ch, it has a powerful Drive channel that can cover a wide range from natural overdrive for singing to modern and aggressive distortion.
・Multi I/O Functions
This is a high quality buffered bypass specification based on CLIONE with a high quality buffer, and can be used as three channels: Bypass, Clean Ch, and Drive Ch.
In addition, a highly reliable and long-lasting digital switching method is used for switching, which eliminates noise during switching and reduces the risk of failure and trouble compared to mechanical switches.
It is equipped with a variety of functions that can be used in a variety of ways in live performance and recording, including a full-fledged DI out with Pre/Post, GndLift, and Phase switches, Tuner out, and a mute function.
・Higher Headroom
This provides the same headroom as an 18V power supply without the need for a special power supply.
Product Specifications
Spec
Basic Spec
Input Power |
DC9V external power supply for effector Current consumption 380mA (Battery drive not possible) |
Number of channels |
2ch (Clean,Drive) + Bypass |
Body dimensions |
W177 x D105 x H51mm |
Clean Ch
Level |
Output level (independent of DriveCh) |
Comp |
Compressor threshold ratio adjustment
Maximum threshold -34dB Ratio maximum 8: 1 |
Atk/Rel |
Compressor attack / release time adjustment
Attack about 2ms-60ms (typ) Release about 50ms-500ms (typ) |
Drive Ch
Comp through |
At the bottom of the switch, the CleanCh comp is also applied to the DriveCh.
No compression is applied to the upper side of the switch and DriveCh. |
Level |
Output level (independent of CleanCh) |
Gain |
Distortion gain adjustment |
Blend |
Adjusting the blend of clean and distortion The clean that is blended is exclusively for distortion Ch.
Adjusted clean sound, independent of CleanCh. |
Bass |
Bass control for DriveCh Shelving ± 7dB @ 150Hz ± 14dB @ 40Hz |
Treble |
Treble control for DriveCh Shelving ± 6dB @ 700Hz ± 11dB @ 2.5kHz |
Master EQ (An EQ section that works for both channels)
Bass |
Shelving Freq=70: ±16dB@20Hz ±8dB@70Hz
Freq=180: ±18dB@30Hz ±8dB@180Hz |
Bass-Freq |
Change the bandwidth of the Bass control |
Lo-Mid Freq |
Peaking ± 18dB Center frequency 180Hz-1.6kHz |
Hi-Mid Freq |
Peaking ± 18dB Center frequency 500Hz-3.5kHz |
Treble |
Shelving ±10dB@2kHz ±20dB@8kHz |
Bright |
It is a switch that emphasizes the feeling of attack. It boosts about 7dB around 1.8kHz. |
Notch |
It is a switch that cuts the midrange naturally. It cuts about 5.5dB around 1kHz. |
Foot switch and PAD switch
Effect ON |
ON / OFF switching for the entire pedal. Bypass is output when the LED is off.
Also, press and hold for about 2 seconds to mute Output / XLR Out. |
Drive |
It is a channel changeover switch
Clean Ch is selected when the LED is off, and Drive Ch is selected when the LED is on. |
-15dB(Input) |
This is a PAD switch for when the signal is distorted due to a high output active bass, etc.
Attenuates the -15dB signal at the input stage |
XLR related switches
Pre/Post |
XLR output pre / post switching
Pre outputs bypass, and Post outputs bypass / effect sound like Output. |
Phase |
It is a phase inversion switch. It is the positive phase of No. 2 HOT at the lower position. |
Lift |
GND lift switch Installed on the lower side (normal), lifts on the upper side |